Starting from unplugging the battery, checking the charging cable to do it flashing ROM, here’s a collection of ways to deal with totally dead cellphones that can’t be charged. Please note, the problem is not always with the battery, but also the device system.
As a result, the cellphone does not turn on, even though it is connected to the charging cable. No need to panic if you face this problem, it’s a good idea to try some of the easy solutions below before going to a professional, that way you will save more money.
How to Overcome a Totally Dead HP?
A totally dead cellphone may be caused by hard contact after being dropped, submerged in water, bootloopold age and many more.
Just apply the solutions in this summary from Sluruls and find out which one has succeeded in restarting your cellphone:
1. Unplug the Battery
Is the problem still persistent and not showing any changes after applying the methods above? Try to implement the following steps:
- Unplug the battery.
- Leave it for a few minutes.
- Then plug it back in.
- Connect the charging cable to the charging port.
- See if the HP is successfully charging or not.
So, how do you deal with a totally dead cellphone with a planted battery? You can try a battery pull simulation, aka Restart, for sure you know how to do it, namely:
- Press and hold the Power button
- Select Restart in the options that appear.
2. Charge HP for a few moments
Starting from the easiest way, namely tocharge MOBILE PHONE. Connect the completely dead cellphone with the charging cable, then leave it for a few hours to see the changes.
If the cellphone can turn on, chances are the battery is dead dropthus making it not want to turn on.
But on the other hand, if these solutions don’t show any positive changes, it means you’re facing a more serious problem, which could be hardware-related. Don’t worry just yet, see the next method below.
3. Clean the Charging Port
The charging port is a small hole on the bottom of the cellphone which acts as a gateway for current to enter the cellphone. There are times when this port gets clogged with dirt particles, thereby preventing the sensor from receiving the current.
You can guess the impact, that is, the cellphone cannot be charged. If it is certain that the port is dirty, the way to deal with a totally dead HP is to clean it.
Use a soft-bristled toothbrush or blunt pin to get any clogged particles out. Do it carefully and gently so as not to damage the sensor.
4. Check the Charging Cable
Charging cables can be damaged if not cared for properly. Maybe there is a cable that is cut because it is often folded or because it is very old.
Try to check your charging cable, is it still working or not. If the cable is damaged, the current flowing is cut off, so it doesn’t reach the HP charging port.
It is recommended to buy a cable from an authorized manufacturer or a high quality cable so as not to damage the adapter.
5. Charge with a Desktop Charger
How to deal with a totally dead cellphone because it runs out of battery can be an alternative to solving your problem. Desktop chargers are special chargers that can be used to charge the battery externally.
- Remove the battery from the back of the HP.
- Then charge with a desktop charger.
- Wait until the power is fully charged, let it sit for a while.
- Reinstall it on a totally dead cellphone.
Unfortunately, this method can only work for older versions of cellphones, and will not work for cellphones that use built-in batteries.
6. Factory Reset from Recovery Mode
The cellphone is stuck in a bootloop for a moment, then turns off again and shows no signs of the cellphone turning on? Are you facing similar problem?
The case is caused by a software glitch, maybe you just finished modifying the system or updating the operating system to the latest version. For this problem there is still hope. Here’s how to do a factory reset via recovery mode:
- Hold down the Power, Volume Up and Volume Down buttons simultaneously for a few seconds.
- You will be taken into Recovery Mode.
- Use the Volume Down button to scroll to the Factory Reset menu.
- Press the Power button to select the menu.
- Wait until the process is complete.
7. Flash ROM
The next way to deal with a totally dead cellphone does require technical treatment, but you don’t need to be afraid of being difficult, as long as you pay close attention to the following information.
Flashing ROM can solve problems caused by damaged or incompatible firmware, so your cellphone can be reinstalled with the default firmware. However, this method is quite risky if done by inexperienced people.
Instead of turning on a dead cellphone, installing the wrong firmware will actually make your cellphone unusable forever. It is highly recommended to visit a professional technician who has experience flashing ROMs.
The tools needed for flashing include a PC, ROM or firmware, USB cable, and a flash tool that is compatible with HP.
8. Visit an Authorized Service Center
It’s a shame if your cellphone still can’t be repaired, even though you’ve flashed the ROM. The last effort that can be done is to visit the nearest authorized service center according to the HP brand that you are using.
Each authorized service center is equipped with experienced technicians who can help identify and provide the best solution. Often they offer help for free.
Find and go to the nearest service assistance center, then consult directly with the officers who are there. They will provide the best treatment for the problem you are facing.
Of the various ways to deal with the totally dead cellphone described above, which solution has been successfully tried? Hopefully one of them can be useful, because seeing a cellphone completely dead is something that is troubling, considering that cellphones are a very important communication device at this time.